vand cabluri tata mama / tata tata / mama mama pt breadbord Arduino nodemcu esp8266 pret la 10buc diverse culori 10cm sau 20 cm lungime
Timisoara, Timis
27 ianuarie
4 RON
oled display 128X64 IIC I2c 0.96 Inch pt. Arduino, Raspberry PI OLED display model 1.3" = 40ron Display OLED I2C 0.96" model SSD1306 Resolution: 128X64 Viewing angle: greater than 160 degrees Supported platforms: for arduino, nodemcu esp8266 esp32, 51 series, MSP430 series, STIM32 2, SCR chips Low power consumption: 0.04W during normal operation Support wide voltage: 3.3V-5V DC Working temperature: -30-80 degrees Volume: 27MM * 27MM * 4.1MM Driver IC: SSD1306 Communication: IIC, only two I O ports No font: The software takes word modulo Backlight: OLED self light, no backlight Interface: VCC: 3.3-5V GND: Ground SCL: Serial Clock SDA: Serial Data
Timisoara, Timis
26 ianuarie
25 RON
Wireless Adapter 150M USB 2.0 WiFi Wireless Network Card 802.11 b/g/n 2.4GHz varianta mini cu antena integrata in stick: 13RON varianta cu antena detasabila cu castig 2db: 25RON
Timisoara, Timis
24 ianuarie
13 RON
HC-SR501 Adjust IR Pyroelectric Infrared PIR Motion Sensor Detector Module for Arduino and Raspberry PI poate fi folosit pt automatizari de ex: aprins, stins un BEC, sau orice aparat electric cand te afli intr-o anumita raza (se foloseste impreuna cu un releu daca tensiunea e mai mare de 5V si amperaj > 200mA) specificatii: Dimension: 3.2cm x 2.4cm x 1.8cm Infrared sensor with control circuit board The sensitivity and holding time can be adjusted Working Voltage Range: DC 4.5V- 20V Current drain:< 60uA The static current:< 50uA Voltage Output: High/Low level signal:3.3V TTL output Detection distance: 3--7M(can be adjusted) Detection range: < 140 Delay time: 5-200S(can be adjusted, default 5s +-3%) Blockade time: 2.5 S (default) Trigger: L: Non-repeatable trigger H: Repeat Trigger (default) Work temperature:-20-+80 C Trigger Method: L unrepeatable trigger / H repeatable trigger
Timisoara, Timis
22 ianuarie
12 RON
module senzor de temperatura si umiditate dht22 42ron model mai precis si mai rapid decat dht11 senzor de temperatura NTC se pot folosi cu arduino nodemcu esp8266 raspberry sau alte microcontrolere am si alte componente si senzori
Timisoara, Timis
20 ianuarie
25 RON
Driver motor pas cu pas, DRV8825, compatibil cu placile de expansiune CNC Shield UNO si Nano. Acest driver este diferit de modelul A4988 deoarece poate fi setat in rezolutia 1 32 si suporta un amperaj mai mare fata de acesta. Specificatii: Tensiune de alimentare: 8.2V - 45V Tensiune logica: 2.5 - 5.25V 6 rezolutii diferite: full, 1 2, 1 4, 1 8, 1 16, 1 32 Curent maxim: 2.5A, ajustabil prin potentiometrul integrat (pentru maxim 24V) 32 segmente de microstepping Protectie la: supracurent, supratemperatura si subtensiune Protectie la polaritate: Nu Dimensiuni mm: 20.5 x 15mm driver motor imprimanta 3D DRV8825 NEMAxx ramps reprap stepper 3D printer cu radiator (current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1 32-step). It operates from 8.2 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling) reglabil: full-step, half-step, 1 4-step, 1 8-step, 1 16-step, and 1 32-step pcb mov
Timisoara, Timis
19 ianuarie
19 RON
Letcon ciocan statie de lipit componente electronice reglabil 60-80W rezistenta ceramica resitenta in timp varfurile se pot schimba usor cu diferite dimensiuni si forme
Timisoara, Timis
19 ianuarie
35 RON
wemos d1 mini esp8266 wifi pt modare PS4 xploit sau alte proiecte de ex IOT home automation etc. am si varianta noua esp32 dualcore Bluetooth cu mai multi pini digitali si analogici la 50ron si alte piese si senzori
Timisoara, Timis
18 ianuarie
25 RON
servomotor MG995 Digital Metal Gear PC car robot navomodele barcute de plasat momeala compatibile Futaba MG995 /MG996 50ron pt cel cu rotatie continua 360grade servomotor MG996 cu rotatie 270grade 50ron cuplu: 13 kg/cm Servomotor albastre SG90s 9g 4.8v..6v max 2.2kg/cm la 6v carcasa albastra 180grade 14ron Servomotor carcasa gri MG90s 9g metal gear 4.8v..6v max 2.2kg/cm la 6v rotatie 270/180/360 20ron
Timisoara, Timis
8 ianuarie
50 RON
modul ESP8266 WiFi NodeMCU Lua pt. proiecte,automatizari tel.O752OO9218 modul Wireless NodeMCU Lua v3 CH340 WiFi bgn (32Mbits) FLASH Lolin development board Based ESP8266 with firmware modulul wifi merge in mod AP (Access Point-la care te poti conecta ca si la un router), STA sau AP+STA modulul poate folosit si programat si prin Arduino modulul poate fi folosit pt. diverse automatizari in casa: pornire aparate (A C, filtre, alarme, lumina-bec impreuna cu un releu si diversi senzori, control roboti etc -totul de la distanta de pe Internet dintr-o singura aplicatie pe telefon sau pagina web Foarte util pt. studenti la proiecte sau copii ce doresc sa invete programare+electronica tel:O752OO9218
Timisoara, Timis
8 ianuarie
35 RON
